Config Reference: различия между версиями
Перейти к навигации
Перейти к поиску
Айболит (обсуждение | вклад) |
Айболит (обсуждение | вклад) |
||
(не показана 1 промежуточная версия этого же участника) | |||
Строка 4: | Строка 4: | ||
#Этот параметр должен быть указан. У нас это "cartesian" | #Этот параметр должен быть указан. У нас это "cartesian" | ||
#max_velocity: | #max_velocity: | ||
− | # | + | #Максимальная скорость(в мм/с) по X и Y. Это значение может быть изменено во время печати с помощью команды "SET_VELOCITY_LIMIT". |
+ | #Этот параметр должен быть указан. | ||
+ | max_accel: | ||
+ | #Максимальное ускорение (в мм/с^2) по X и Y. Ставь то ускорение, которое не ломает твой принтер и на котором нет пропуска шагов. А ускорения для печати настраивай уже в слайсере. | ||
+ | #Указанное значение может быть изменено во время печати с помощью команды SET_VELOCITY_LIMIT. | ||
#Этот параметр должен быть указан. | #Этот параметр должен быть указан. | ||
− | + | #minimum_cruise_ratio: 0.5 | |
− | + | #Most moves will accelerate to a cruising speed, travel at that cruising speed, and then decelerate. | |
− | + | #However, some moves that travel a short distance could nominally accelerate and then immediately decelerate. | |
− | #minimum_cruise_ratio: 0.5 | + | #This option reduces the top speed of these moves to ensure there is always a minimum distance traveled at a cruising speed. |
− | # | + | #That is, it enforces a minimum distance traveled at cruising speed relative to the total distance traveled. |
− | + | #It is intended to reduce the top speed of short zigzag moves (and thus reduce printer vibration from these moves). | |
− | + | #For example, a minimum_cruise_ratio of 0.5 would ensure that a standalone 1.5mm move would have a minimum cruising distance of 0.75mm. | |
− | + | #Specify a ratio of 0.0 to disable this feature (there would be no minimum cruising distance enforced between acceleration and deceleration). | |
− | + | #The value specified here may be changed at runtime using the SET_VELOCITY_LIMIT command. | |
− | + | #The default is 0.5. | |
− | + | #square_corner_velocity: 5.0 | |
− | + | # The maximum velocity (in mm/s) that the toolhead may travel a 90 | |
− | + | # degree corner at. A non-zero value can reduce changes in extruder | |
− | + | # flow rates by enabling instantaneous velocity changes of the | |
− | + | # toolhead during cornering. This value configures the internal | |
− | + | # centripetal velocity cornering algorithm; corners with angles | |
− | + | # larger than 90 degrees will have a higher cornering velocity while | |
− | # | + | # corners with angles less than 90 degrees will have a lower |
− | + | # cornering velocity. If this is set to zero then the toolhead will | |
− | #square_corner_velocity: 5.0 | + | # decelerate to zero at each corner. The value specified here may be |
− | # The maximum velocity (in mm/s) that the toolhead may travel a 90 | + | # changed at runtime using the SET_VELOCITY_LIMIT command. The |
− | # degree corner at. A non-zero value can reduce changes in extruder | + | # default is 5mm/s. |
− | # flow rates by enabling instantaneous velocity changes of the | + | #max_accel_to_decel: |
− | # toolhead during cornering. This value configures the internal | + | # This parameter is deprecated and should no longer be used. |
− | # centripetal velocity cornering algorithm; corners with angles | ||
− | # larger than 90 degrees will have a higher cornering velocity while | ||
− | # corners with angles less than 90 degrees will have a lower | ||
− | # cornering velocity. If this is set to zero then the toolhead will | ||
− | # decelerate to zero at each corner. The value specified here may be | ||
− | # changed at runtime using the SET_VELOCITY_LIMIT command. The | ||
− | # default is 5mm/s. | ||
− | #max_accel_to_decel: | ||
− | # This parameter is deprecated and should no longer be used. |
Текущая версия на 15:56, 20 февраля 2025
[printer] kinematics: #Тип кинематики принтера. Он может быть: cartesian, corexy, corexz, hybrid_corexy, hybrid_corexz, rotary_delta, delta, deltesian, polar, winch, or none. #Этот параметр должен быть указан. У нас это "cartesian" #max_velocity: #Максимальная скорость(в мм/с) по X и Y. Это значение может быть изменено во время печати с помощью команды "SET_VELOCITY_LIMIT". #Этот параметр должен быть указан. max_accel: #Максимальное ускорение (в мм/с^2) по X и Y. Ставь то ускорение, которое не ломает твой принтер и на котором нет пропуска шагов. А ускорения для печати настраивай уже в слайсере. #Указанное значение может быть изменено во время печати с помощью команды SET_VELOCITY_LIMIT. #Этот параметр должен быть указан. #minimum_cruise_ratio: 0.5 #Most moves will accelerate to a cruising speed, travel at that cruising speed, and then decelerate. #However, some moves that travel a short distance could nominally accelerate and then immediately decelerate. #This option reduces the top speed of these moves to ensure there is always a minimum distance traveled at a cruising speed. #That is, it enforces a minimum distance traveled at cruising speed relative to the total distance traveled. #It is intended to reduce the top speed of short zigzag moves (and thus reduce printer vibration from these moves). #For example, a minimum_cruise_ratio of 0.5 would ensure that a standalone 1.5mm move would have a minimum cruising distance of 0.75mm. #Specify a ratio of 0.0 to disable this feature (there would be no minimum cruising distance enforced between acceleration and deceleration). #The value specified here may be changed at runtime using the SET_VELOCITY_LIMIT command. #The default is 0.5. #square_corner_velocity: 5.0 # The maximum velocity (in mm/s) that the toolhead may travel a 90 # degree corner at. A non-zero value can reduce changes in extruder # flow rates by enabling instantaneous velocity changes of the # toolhead during cornering. This value configures the internal # centripetal velocity cornering algorithm; corners with angles # larger than 90 degrees will have a higher cornering velocity while # corners with angles less than 90 degrees will have a lower # cornering velocity. If this is set to zero then the toolhead will # decelerate to zero at each corner. The value specified here may be # changed at runtime using the SET_VELOCITY_LIMIT command. The # default is 5mm/s. #max_accel_to_decel: # This parameter is deprecated and should no longer be used.